PlayVital Full Set Protective Skin Decal for Steam Deck LCD, Custom Stickers Vinyl Cover for Steam Deck OLED - Black Silver Carbon Fiber

It was so easy to put on and it looks great! Very vibrant and a clear image! It has a good grip on my steam deck when pushing it down to fully adhere it to the surface, and the size fit is perfect and covers everything without overlapping or not being enough!

Great price for a pair. Easy to install, looks great. The trick is to install the front touch pads first, for the front and the back bumpers for the back. Peel about ⅓ of the decal going left to right and adjust accordingly, match the square touch pad and screen. for the front; line up the top and the bottom borders going around the screen, for the ⅔ of the decal. Once you got to peel the whole thing off it should fit just right. ( remember to remove the tiny decals covering the speaker holes.) For the back do the same, start from left to right this time peel ⅔ of the decal and line up the vent holes first. Once those line up it should fit perfectly.

I decided to try one of these skins because they're cheap and wanted to see if I could install one before spending the big bucks. I would recommend watching a video on how to install it, because it doesn't come with very good directions. It did come with two sets, which is nice if you mess up. I followed the video and didn't have any issue. It does take some time and patience, and you may need a toothpick to help remove some of the small parts of the sticker - like the speaker holes. Some parts stuck to the paper too much and were difficult to separate. The yellow part of the design were the hardest to see and separate. I think the design I picked looks pretty good, finer detailed designs might not. So far I haven't had any issues with it peeling, but time will tell. Edit - I didn't have any issue with the skin peeling or anything with a lot of daily use. I peeled it off on purpose and it didn't leave any residue at all. I'd buy this brand again.

Its been 4 years and this skin is still permanently stuck to my steam deck i even dropped it in water once. That broke my heart that day but i fixed my steam deck and this skin never lifted off once this thing is a beast.

These are /alright/. There’s two in the pack and the first one I put on without a heat gun after cleaning the deck with 90% alcohol because I was impatient. The skins have a nice feel to them and the image on it was pretty good quality. It took about two weeks before the edges started peeling up. Not a lot just enough to catch cat hair and be annoying. The thin strips around the screen don’t stick for anything. I peeled that one off and it left quite a bit of residual glue which I cleaned off pretty easily with more alcohol. The second skin I put on with a heat gun. Went on much easier and has a much flatter feel to it. It’s been on much longer before I started having issues with peeling, mainly on the sides where my fingers got up to the triggers and on the back buttons. This is a nice temporary skin to keep the deck safe while you wait to get a better skin but don’t plan on it being permanent.

My steam deck looks great with the new skin on. It came with a spare skin in case you messed up which is awesome in itself! (As most products normally only give you one). Install wasn’t bad, a little tedious to get the corners aligned. I flattened out the skin from one end to another to prevent any bubbling. After that I used my wife’s hair dryer to heat up the skin while pressing on the skin with a card, which helped with the adhesion. It’s been on for a few months now with consistent gaming with no issues! I also bought the grip textures and it looks amazing altogether!

Update 9/23 Removing will leave vinyl glue everywhere. An absolute mess to remove. Glue gunk will get everywhere on the system when trying to remove the glue. Don't buy. Would give 5 stars if it was cut better and was a little more accurate. For the price and comparison to others I think it's a good trade-off. The laser cutting leaves something to be desired. The vinyl is not 100% accurate but very close. They provide two full skins per pack so you can try if you completely fail the first time. The laser cutting missed a spot on both prints I purchased so theres a small jaggy. Sometimes the laser cuts too deep and you have a hard time separating the print from the paper and the paper comes with. Even perfectly aligned in the center of a zone, you'll still have some minor misalignments. The instructions are weak and are for a ps4. This is a much more intricate install. Dbrand has a good install video that will suffice but you take the same approach because dbrand uses 3m paper. You're best to just freehand it. It will not be pixel perfect. Using a hairdryer does help to smooth it out. A word of advice is to carefully pop out all the speaker pips before you remove the vinyl from the paper because its near impossible to remove them later. They should just stick to the paper when you peel but they don't.

This product is NOT as easy to apply as it is advertised and shown in the tutorial video. You need steady hands and a keen eye for detail because this will stick on there easily which can make easier to tear and fine adjustments harder. Both of my front panels tore a little bit when trying to peel it of the paper back. The edges turned out bumpy in some areas and some corners do not stick down as intended. They do give you two in case which is nice, I guess. The process of putting it on took my 45 minutes with all the adjusting, the first on tearing, deep analying the tutorial video to figure how on god's green earth the got it to align so easily, and attemping to smooth out all the bumps. Overall the skin quality feels cheap and might consider taking it all off if the tape-like edges keep bugging me. The only reason this isn't a 1 star review is that I will acknowledge there could be user error when installing but you shouldn't have to a intermediate gundum model builder to be able to put on this "easy to install" skin and have it nice and flush with the machine.

First of all, adhesion is brutal. I did manage to get the back one sticker on completely flush (to my surprise) and even after heating and the rest of it, there's still peeling that started a few hours later. The front one I gave up on as both (it comes with 2 sets) just didn't line up in some way. Whether it was the venting grills or around a button, the fit just wasn't there. I'm glad some people are having success with these skins. I'm not going to both with a refund but if I can save someone else from this, that's worth it

Applied without a problem , 2 decals in the package which is nice to have, only issue I am having is that decal strip on bottom and upper edge of screen keeps peeling away , have to constantly keep pressing it back which is annoying , maybe not sufficient glue ,otherwise good product

I would recommend this

Perfect decoration for the Deck. Looks beautiful after a little bit of trying. Luckily I got two sets.

Great!