DEWALT TOUGHSYSTEM 2.0 Tool Organizer and Storage 3 Drawer Unit (DWST08330)

These are great drawers, that fit certain needs ie no locks, but are sealed. If you're not running Toughsystem already, I'm not sure why you'd be looking at these, but these might even be worth making adapters for to run these drawer units for your specific needs. They hold up very well with a fair amount of weight on/in them and don't sag. I even have a set of these just inside my rear truck door inside the cab for quick access to tools and they've held up to years of southern US heat. Now that's not a great use for these boxes, but I was worried about the heat affecting boxes and they hold up and it just happens to be a convenient location for one of these drawer units. Where DeWalt has an edge other drawers/systems is that they are sealed. Put these in the back of an uncovered truck or trailer and your tools or equipment won't be rained on. And of course they are stackable, though they do rock a little bit when stacked. If I'm moving them in an open truck bed I usually don't stack these terribly high. Inside a truck bed I usually keep just a couple Toughsystem boxes stacked and I still like quick tool access so I would typically run a drawer box with either a small or up to a large box or even a tote on top, so I don't have to do any unstacking and if I need to move a large amount of tools to wherever I'm working, I can put these in the DeWalt dolly or one of their large wheeled boxes and when I get to where I'm going I'll break these down minimally for complete and quick access. I've got experience with other drawer systems as well. I originally got the very first DeWalt Toughsystem drawers and they were horrible, but if it wasn't for the DeWalt dolly and the Totes, I would have likely switched to Rigid or Milwaukee. Rigid I just like the way a lot of their system was priced. Milwaukee just simply has so much available and their mounting platform is really nice and I see these everywhere and I really like them, but not quite enough to want to pay for them. Tstak/Versastack drawers just seem too small and flimsy to me. I like Toughbuilt, but they don't seem to have a large enough system released and availability is low with a price tag just high enough that I haven't bit, though I've always been impressed with Toughbuilt. The bigger DeWalt versions are nice, but just too big and too expensive for me. If I were moving these around with a forktruck that might be different, but even then I would then just use a nice metal toolbox and make some sort of subframe. I don't remember if these work with the DeWalt racks. I assume they do, but the rack system matters less to me with these drawer units. FYI the Toughsystem tool trays don't fit. Most bins don't work with the shallow drawers, though I've used some aftermarket ones. I have been storing wrenches, small sockets and pliers in my 3 drawer unit. I have another 3 drawer unit that I will likely use for camp kitchen duties. The 2 drawer units are probably more versatile, but if you've got enough stuff that fits in the 3 drawer unit, it's a great addition. If you're already into Toughsystem, get these drawer units and a couple 2 drawer units. If you're granularly looking at all the complete systems, DeWalt is a top contender, though most guys will go Milwaukee I think most of these different systems have pros/cons and all will work really well if you'll just simply use them and adjust when you find something you don't like. When I was young we often just used buckets and that worked too, it just required more digging around.

I will get straight to the point yes I do like this three drawer toolbox and I even bought the two drawer one. I have no major regrets whatsoever. I think they are reasonably priced compared to the competition. If you need more information than that then continue reading. I’ve had the three drawer box for about 6 months now and no issues so far. I also have the two drawer that I just bought about 2 months ago. The 3 drawer fell off my work cart a couple weeks ago but fortunately it did not damage it at all. It just scuffed it up a little bit. The three drawers hold a lot of tools, more than you realize. They also lock in place when fully closed, which is nice feature because you don’t have to worry about the drawer flying open and spilling all your tools all over the place. Yes, I wish it had a handle on the top in addition to the handles on each side but I think they did not put one on the top because it might warp the box and affect the way the drawers slide out after a while. Some Australian guy on YouTube did modify his and put handles on the top and he did a really good job because it looks factory done. Another positive thing that I heard about these, but haven’t tested myself yet is that they are rain tight so if you happen to leave them in the back of your work truck and it rains, you won’t get water in your tools, of course I would never leave my tool boxes exposed out in the back of my truck unless it’s just for a very short time. Having both the two drawer and three drawer and the way they lock on top of each other, works out perfectly for me. I love being able to just open the drawer and pull a tool out versus digging through a tool bag. Also, the toolboxes by themselves without any tools in them, don’t weigh very much at all, but I honestly don’t know what the weight is, but obviously a lot less than a metal toolbox. I’m very very pleased with these boxes so far.

It works great for hand tools. Packed full of wrenches, pliers, and anything else that'll fit. Drawers slide great with a positive latching system. If you get generic toolbox drawer liner and cut to fit, it almost completely cuts out the rattle when driving on dirt roads. Great box. Would buy again.

This really work well for me getting some clutter off the work bench. This box is very well made, the draws slide easily and the latches work great.

A good stout three drawer chest that is serving me well as a tool box. Don't forget to pick up some rubber drawer liners.

I like how the drawers function so far. The plastic chosen for the interior drawer sides and bottoms is questionable and doesn't seem as durable as packout and others offerings (feels more like rigid abs than polypropylene). I'll be retro fitting the upper handle as seen online and YouTube. The dewalt toughsystem clip system is still not great and the plastic molded lips/clips that lock into the latch system are not durable. However I was already bought into dewalts tough system prior to packouts launch years ago and the only truly redeeming quality to toughsystem is the ds carrier and the ability to fabricate rack systems for their ds brackets with 1" square tubing or use pairs of large metal "L" brackets screwed to plywood. The ability to pull individual boxes out of the rack and carrier still makes up for toughsystems other shortfalls. For what it's worth, for most users, I would invest in the drawer boxes and parts organizers and not buy the standard boxes of any manufacturer unless you absolutely need the larger sizes for a specific storage need. The drawers make getting to tools, bits and parts much easier than stacking and unstacking boxes, both in a van or truck and on site. Packouts cleat system is still superior but dewalts drawers and boxes can be had much cheaper , especially with Home Depot's new buy more and save on toughsystem. These drawers definitely are closer to systainer durability than packout but for personal use and owner operators who take care of their tools and equipment they are definitely plenty robust.

I love this tool box. After we moved, the tools were just spread over everywhere. This toolbox keeps everything organized. It holds a lot and is incredibly well made. I may ask for another one as a gift.

Great addition to my Dewalt 2.0 system. This is heavy duty and the drawers are solid and open and close easily on ball bearing tracks. They fit my bigger tools and I also have the three drawer box for my smaller tools. If you don't have this system, get it and get one of these as well. I recommend this product.

スライドレール、ロック付きなので走行中でも開きません。

The DEWALT DWST08330 ToughSystem 2.0 3-Drawer Organizer is an absolute beast at keeping tools sorted, protected, and easy to access. I picked up two of them, and honestly, I'm glad I did. I mean, once you start organizing with these drawers, you realize how much time you've been digging through clutter. The build quality is classic DEWALT: rugged, durable, and job-site ready. The drawers slide smoothly even when fully loaded, and the latches feel solid. I especially love that the drawers have individual side latches to keep them from opening during transport. Inside, the customizable dividers make it easy to set up perfect compartments for bits, fasteners, hand tools, electrical gear—whatever you need. These also stack seamlessly with the rest of the ToughSystem 2.0 lineup, making integration into an existing setup effortless. If you're serious about a cleaner, more efficient workspace, these drawers are absolutely worth it. Buying two was the right call—I highly recommend them!

Great for putting things in! And if you fill all of the first drawer, there's a whole second drawer!! A-maze-a-ing!!

Excelente!

Muy Buena calidad de materiales, sin llegar a excelente. Es un gabinete práctico y funcional.