5V USB COB LED Strip Cool White 6000K Dimmable IP65 Waterproof 6.6ft | 2M CRI 93+ USB Powered 640LEDs with Dimmer High Brightness Flexible LED tape lights

Exactly as expected. Glows very brightly at first, and then dimply for a very long time.Responds well to a blacklight"This would be a good one to cut up into little ceiling stars or designs for a kids room.

These are really great, but hard to get the double sided tape peeled off completely.. Bending backward slightly will make the tape cover mound up enough to get a small blade through. Perfect for accepting motorcycles with a USB power port.

Wrapped around bottom tube of a Felt VR40 (43cm frame) bicycle. Using RavPower 20,000mAh power bank with output of 2.0A. Uses about 14% per hour of continuous illumination. Aiming to gain more visibility while riding, in case I'm caught in dark hours. Took about 3 hours to finish.VERY BRIGHT in sunset hours and dark environment as if having flashlight and underglow at the same time. COB LED is more continuous compared to other more spaced out versions.Back of entire strip does not have adhesive. So wrap as tightly as you can then finish off with zip ties. Pretty flexible to keep 45° angles wrapping without compromise. Keeping 1.5" apart.Will update as new variables arise...

These COB LEDs are great,I bought these to be more visible at night and even during the day. The lights are very cool looking too.Just be careful when it's time to peel the sticky covering off, go slow and gently, you can easily pull sticky strip right off the light strip if not paying attention.I had to buy a second strip to even the lights out on the bike frame. So far it's been a month and still staying in place, even after getting wet. Recommended

I'm totally blind. I know that I'm kind of strange and do some strange stuff a lot of sighted people wouldn't! LOL.But anyway! I got this because I've had my taxi drivers more than one tell me it is hard to see the address on my house at night. I have 5 inch high numbers on the garage door and they still have trouble! I live at the end of a one way street! So the Taxi drivers must come around the end of the street and at one point, the lights from the car will hit my garage door. But they still really couldn't see the numbers. So I got this to put across the top of the garage door frame on the under side of it to shine down onto the door of the garage in hope it would make it easier to see the numbers. This almost goes from edge to edge. It only lacks about 9 inches on each side or so. From what I've been told, it lights up the top panel very well and going down the light is dimmer!I had someone who could see take a few photos with the light off and on at night to try to show the improvement? It was cloudy out and he told me, do to the clouds, we whir getting a reflection from the clouds some.

I use this with my 3D printer to get more light into the print area. The color is a cool white and the brightness is adjustable. The sticky backing on it holds just great against the PETG mounting I printed for it. There is no timer so you will have to turn it on or off manually or get one seperately. If you are using the P1P/P1S don't plug it into the internal USB, there isn't enough power for it there.

these things are horrible...dont waste ur money...the adhesive back is junk...and it stuck to the protective paper so there wasnt any adhesive on the strip itself...complete junk...

I used it on my bike at night it is bright.

Not really orange in colour

It was on fire while I was charging it

So my main gripe with this is that the pictures don't exactly match the product; there is no silicone over top of the entire surface, only the silicone used as the LED COB itself. I went into this knowing that might be a risk (I forgot to look at other review photos, silly me) but it's still disappointing. Bare copper is exposed at regular intervals along the length of the strip, so if this is a concern for you, aim for something IP68 rated.Anyway, some helpful info:For the entire 2m length, power draw at 5.0V is just shy of 2.0A (10W). Most of my USB power supplies drop voltage a bit at this load and end up supplying 4.8V at 1.6A (despite claiming 2.4A capacity; shoddy power supplies I guess, not a dig at the LED strip).If you're using this as a light strip in a Bambu Lab X1/P1 series printer, be aware the built-in USB outlet only provides 1.5A, and so the strip should be cut to a maximum length of 1.5m.