Speaker Mount for Wall and Ceiling, Low Profile Heavy Duty, Anti-Theft, Universal for Channel Surround Sound and Satellite Speakers, Black, 2 Mounts

Got these to hang HTD Level 3 center and L/R speakers. These are heavy speakers, at 26lbs for the center and 19lbs for the L/R speakers. Mounted into drywall, some with studs and some without. Overall, I'm very happy with the mounts. They're sturdy, well built, and the safety wire is a nice touch. They do hang off the wall several inches, but still look good. Installation is generally easy - the speaker-side bracket screwed into my HTDs' pre-drilled holes and used the speaker's own screws no problem, and the wall-side mount just required drilling some holes, tapping in the plastic drywall anchors, and screwing in the screw and washer. Like every included plastic drywall anchor I've ever used, several of them deformed when I tried to tap it into the wall, but I had some different drywall anchors on hand and used those for the occasional replacement. I think I replaced two of 12 overall. Speaker actually attaches to the bracket by inserting a metal peg that's part of the speaker bracket into a round hole that's part of the wall bracket and tightening a turnable lever to pinch the peg into the hole. My one complaint, and it's fairly minor, is that the speakers noticeably sag with these mounts. It was pretty concerning initially, but I don't see any signs that the mounts are coming away from either the speaker or the wall, and so they seem to be securely attached, even if they don't 100% look it. I'm not sure the mounts could be both adjustable and not sag, especially with speakers this heavy, though I have them set up to adjust left-to-right, and the sag is up and down. I'm giving them 5 stars for the benefit of the doubt, but would probably actually rate them 4.5 stars. Good value for money at less than $10/bracket.

Solid mount. I've had RP-205S and RP- 500SA mounted on these and fits with no problems. The install is self explanatory and the provided hardware is enough to do the job. Small and unobtrusive. Great value for what's out there. Only gripe with the functionality is that I wish there was a swaying feature where it juts out of the wall, then it'll be perfect.

I really do like these brackets. They are very well made and very sturdy, with a lot of adjustment possibilities but lacking in one adjustment. If you install these on the wall and want to point them down, they work will. I did that, but I also wanted to turn them inwards to face a little toward each other, and while I managed to achieve this, I had to get creative and swivel the speakers so that are no longer 'straight up and down', but more twisted a little, if that makes sense. I would buy them again for sure, but knowing that limitation is something I have to deal with. The finish is pretty good, they appear powdercoated and I suspect they will last well in the metal workshop I installed them in.

Nice solid looking mount. Had to spend a bit of time with adjustments to get my angles right but got it worked out. I mounted them opposite of how they're designed but it is how my install needed to be. After my modifications they perfect for my JBL garage speakers. Hooked up to a Fosi Bluetooth 2+1 amp (10" sub under my workbench) and everything sounds great.

Very nice mounts. Worked perfectly for my ceiling installation. If needed would buy again.

These sturdy brackets can clearly hold some serious weight. I like that they are fully articulating, The base swivels, the joint can move 180 degrees and the rotator cuff that holds the speaker attachment element can rotate 360 degrees. More exciting (at least for me) is that the speaker attachment "head" can come off, so if you have post mount speakers (as I), then it is a simple matter of putting your post mounted speaker into the hole and tighten down the screw. Oh and the unit has as added safety measure for your speaker (should you use the head). There is a substantial wire tie between the base and the swivel head (just in case). The unit stands approx. 4"x4" with a 3/4" rise. The base shaft is approx. 1" round and is about 1 3/4" high where it attached to the knuckle joint (which itself is about 1 3/4" round). From there the shaft to the speaker attachment is the same as the base shaft. The speaker attachment "head" is a sturdy plate approx. 3" across x 1 3/4" wide;, with screw slots at each end.

These mounts were the best mounts I could find for heavy speakers. I mounted 4 Klipsch S3's with these mounts and they worked perfectly. Many of the reviews mentioned that these will not work with keyhole mounted speakers. That statement is inaccurate. I mounted these using the keyhole slot and they worked fantastic. All I did was remove the mounting plate that is supposed to attach to the speaker, exposing the post. I did have to remove the keyhole bracket from my speaker, insert the post and tighten it down with the provided bolt, then reattach the keyhole bracket to the speaker but this made the installation really secure. Then all I had to do was mount the bracket to the wall and slide the speaker with post into the bracket and tighten with the thumb screw. I did use the included security wire to attach the speaker to the wall in case the speaker was ever to fall. These have been mounted for several months and are holding strong. Highly recommended.

I purchased a pair of inexpensive book shelf speakers, using these mounts and screws that came with the mounts, I screwed them into the top my inexpensive speakers so they could be ceiling mounted. The mounts are very sturdy, easy to assemble. You can take easily them apart via a wing nut so you don't have to hold the speaker and manually screw in wood screws. You can attach both halves individually, then lift the speaker into place and put the wing nut back on, very easy. Also comes with a metal safety tie so that if by chance the wing nut comes loose, it'll keep the second half and your speaker from crashing into the floor, or worse, someone's head. Highly recommended, although your use will probably vary over how I mounted my speakers.

Llevan casi 3 años soportando pesadas bocinas BOSE de 6 unidades y son super discretas.

Great mounts for my 10 lbs. Paradigm Titan book shelf speakers, as i am limited to room in my house and decided to hang speakers from the ceiling. I looked at many mounts , but these caught my eye just due to the design and construction of these brackets so had to try them, Great product in my books and has a safety cable incase of a detachment of mounts.

Super strong. Well built. Nice matte finish. Feels like quality and very suitable for heavier speakers. Great adjustability.

Desde que comencé a buscar soportes para mis bocinas el tema que más me preocupaba era la resistencia y calidad de construcción de estos. Nadie quiere que sus bocinas se desplomen de dos metros de altura de repente. Vi muchos soportes en Amazon y aunque me parecieron interesantes, había opiniones mixtas respecto a la calidad de materiales, por lo que terminé optando por estos, los cuales aunque no me parecieron tan atractivos visualmente, tenían muy buenas reviews en general. Puntos a favor: - Son unos soportes muy resistentes, se nota la calidad desde que los sacas de la caja y los tocas. - Son bastante manipulables, por lo que si la forma en la que vienen no cumple o no se ajusta a tus bocinas, puedes intercambiar piezas de lugar para lograr el objetivo. En contra: - Tiene un diseño muy particular para un tipo de bocina particular, lo cual hace que para bocinar diferentes a lo esperado el ajuste pueda ser tedioso o más complicado. - Si bien incluye algunas piezas extras para ajustarse a tu tipo de bocina, son limitadas, y lo más posible es que tendrás que terminar yendo a comprar tú tornillos o tuercas extras para terminar montando todo de forma adecuada. A pesar de los contras, creo que estos son pasables considerando la buena calidad de los materiales y la flexibilidad de los soportes, permitiendo diversos ajustes y ángulos. En mi caso las utilicé para colgar unas bocinas Definitive Technology Promonitor 800, con las que requerí de hacer unas cuantas modificaciones a las bases hasta obtener el resultado esperado.

Not as strong than expected but it does the job.