KF4002 Panel Dolly, 600 Lbs Capacity, Drywall Mover Plywood Mover with 8" Non-Flat Wheels, 0~10 Inch Adjustable Clamp Panel Car Door Dolly

I bought this to move around a hitch carrier for a wheelchair, it has made it so much easier. It’s heavy duty enough to carry the hitch carrier, and the fact I can resize it means I can use for other things around the house as well.

I needed a way to roll my 24' extension ladder around as it almost too heavy for one person to move. This panel dolly was perfect for the job! It came in a sturdy cardboard box, shrink wrapped to hold all the pieces together in a nice easy to handle bundle. There was no assembly instructions included but it was easy to put together. Included are two eight inch airless rubber wheels, four washers (two for each wheel, one washer is placed on the axle before the wheel is installed and the other washer is placed on the axle after the wheel is installed), my kit had three R-clip pins to fasten each wheel to its axle so I have a spare, there are two heavy duty 14" x 1" square chrome plated steel tubes, and 4 thumb nuts used to fasten the 8 1/2" tall heavy duty steel sliders to the tubes. The thumb nuts make it easy to adjust the width of the dolly to match your load. The box says the panel dolly can accommodate loads upto 9" wide but I found I can actually go almot to ten inches. The box says the clamping plates are 15"x16" but mine are actually 8 1/2" tall by 16" wide. For moving doors and paneling, I like the 8 1/2" tall height. With loads, the panel dolly rolls very nicely. This tool will make a nice addition to my tools. If your looking for a well built, heavy duty panel dolly, you should try this one out. I am sure you'll like it as much as do.

First understand what I’m using this for. I need to move sheet goods from the driveway out front to the back yard workshop, etc. While not a moon scape, the route does include tall grass and some uneven zones. This requires a decently sized wheel. That is why I purchased this product. The wheels could have been bigger, but they worked. The blue side plates are good, heavy construction. Problem #1: As noted in numerous other commentaries, the wheels can be problematic. Note the hub working itself out of the core in the second picture. This happens with any lateral load on the critter, which is almost impossible to avoid. Solution: Add enough washers (inside and outside) to keep the hubs seated without impeding rotation of the wheels. Problem #2: It is almost impossible to get the screws holding the cross bars tight enough to prevent sliding. If the sheet goods tilt even the slightest, they lever the sides apart sufficiently it becomes a challenge to steer and keep the sheets aligned with direction of travel. Solution: I would suggest the manufacturer supply rough textured cross bars. Give those set screws something to grab. Problem #3: If the wheels encounter something they have to climb over, a hole, whatever, the wheels might bog down. Then the panels slide through the device, and you are stuck. Or they’ll twist in such a way as to force the thing to spread out. Even if you have someone fore and aft somebody has to kick the thing to get it to move again. Solution: Here is where the shadetree mechanic shines. In the picture you will note a rope run under the bar and wrapped around the set screws. Make sure the rope is on both sides of the panel. I was moving two to three sheets at a time so to keep them fom flopping about I put C clamps on top at both ends. It also gave me a positive hold I could push and pull on. I took the rope up both sides of the sheets and tied it off to the front clamp. When pushed from behind or pulled from the front that rope stays taught and keeps the dolly moving when the sheets are moving. No sliding through the slot! The rope being on both sides of the sheets also means that the front is going to point where you turn it. No twisting in the fixture and a reduced tendency to fall sideways forcing the gap open. Even if you have two people managing the move, this simple element reduces the total effort required. No, it won’t work through mud. But it dealt with the hoses, foot path pavers, and small yard divots fine. I suggest the manufacturer clean up this idea and put it in the assembly instructions. I'll use this for years to come.

This cart has come in extremely handy on multiple occasions. I originally bought it to move, but still find uses for it regularly. It is pretty light and the perfect size which make it easy to move around or store, extremely well made and sturdy. Extremely happy with my purchase it was a great value and I have more than gotten my moneys worth from it.

Company was great to work with. My wife and I had to haul 6' x 8' fence sections which were too heavy for her to help me. Bought this unit and set the fencing into it, and we both were able to roll it about 100' to place the fence panels where they needed to go. Ground wasn't the most level with holes and mounds, but we were able to roll it along and saved our backs. Very useful tool.

I didn’t have a huge amount of weight in it but when it gets any side pressure at all it tends to let the tires slide away from the rims. Other than that it gets the job done

It worked very well for moving a queen mattress. Very useful to have for moving such heavy items that your wife just can't help you do. Wink! Wink!

broke right away

Good product. Can fit 3 fence panels onto it. Easy to manoeuvre, saves your back

会社で資材運搬用として購入しました。 1枚あたり約25kgある大きな板を運ぶ作業が多いのですが、このKASTFORCE KF4002を使うようになってから、一人でも安定して運べるようになりました。 耐荷重250kgの仕様は伊達ではなく、かなりしっかりした作りです。 フレーム剛性が高く、荷物を載せてもたわみや不安定さを感じません。 キャスターの動きも非常にスムーズで、方向転換時もストレスがなく、狭い通路でも扱いやすいです。 タイヤの回転も滑らかで、重量物を載せても軽い力で押し出せます。 パネル部分のサイズ感もちょうどよく、板やドア材の運搬に最適。 使用後は立てて収納できるので、作業場でも邪魔になりません。 以前は2人がかりで運んでいた荷物が、今では1人で安全に動かせるようになり、作業効率がかなり向上しました。 現場作業用や倉庫での使用にも安心しておすすめできます。

Pesa y hay que ajustar el ancho bien. pero cumple su función

I had to drill out the box beams so the thumb turns would lock the mouth in place. I use it for moving steel doors during large commercial warehouses construction. Rolls over extension cords on slab no problems. A bit pricey… but solid and fuctional.

ボードではなく、65インチディスプレイを運搬する為に購入しましたが、バッチリ活躍しています。もう少し軽いと良いと思います。