8pcs 3D Analog Joystick for Xbox One/Elite Also for PS4 Controller

I bought a set of these for a standard white wireless xbox one controller. As far as quality goes they seem well built, and the one I installed has worked well for me. It might be a slight bit looser than the OEM joystick that came with the controller but that doesn't bother me. There are no dead spots in the new joystick and the drift that I had before installation is now gone. From the reasearch that I have done it is very difficult to find OEM joysticks. If you can find them they most likely will be much more expensive. I think that all of these generic joysticks probably come from some factory somewhere, there maybe duds in whatever product you end up buying whether its this product or another. They all seem to be very similar. For the price I couldn't be happier. If you want to use this product or another similar product you need these items listed below. 1. Most importantly understanding what you are getting into. DO NOT ATTEMPT THIS IF IT IS A NECESSITY FOR THE CONTROLLER TO WORK AGAIN, OR LIKE BRAND NEW. If it is a necessity please save your money and buy a brand new controller. That is not to say that if you do this project your result will not be good or like brand new. You could have a controller that works better than it ever did, but there are no guarantees with this sort of project, it may be a useless piece of garbage after attempting to fix it. This process took me about an hour to do, but I have experience fixing electronics and SOLDERING. There are quite a few videos on youtube how to install one of these joysticks. I highly recomend watching 2-3 videos to see how people have done it. 2. You need a good soldering iron. Please do some research as to what kind you should get. Weller makes some good irons. 3. You Need Solder Wire, it is important make sure you buy electronic solder not any other type for welding, sweating, ect. 4. You NEED desoldering wick if you want to replace the joystick, because the old joystick is not coming out without this. Personally I use 2.5mm wick that is just my preference. I recomend ordering at Home Depot, its $3 for 5 ft (which is way more than enough). 5. Electronic soldering flux makes this process actually happen. The desoldering and the soldering both may require small amounts of flux. Flux helps to direct the solder into the holes where it needs to go or help it transfer from the board into the desoldering wick. I certainly needed it with the solder I was using. *6. This is not mandatory but I like using and a soldering stand aka "helping hand". Its a simple little stand with 2 clips on it to hold the board in place while working on it. Hopefully this list helps you in your quest to fix your controller. Good Luck!

Ok. So my Xbox one elite controller had left side stick drift. Before I ordered these I did everything I could to try to remedy the issue but to no avail. Cleaned with alcohol, blew out with compressed air multiple times and nothing. Still had stick drift. I figured that I would try these replacements. I didn't solder, I just simply removed the inner piece (looks like a disc made out of plastic and metal) I watched a couple YouTube videos to see process. I didn't completely disassemble, although I did in the past for my previous attempts. I took apart the controller enough to bend the green compartment open just enough to remove the disc. I then opened the new units I received (the ones I'm reviewing), removing the green cover, took out the new disc, put it into my controller then put it all together. Works perfectly. If it fails I will update this review but so far so good. Saved myself a lot of money and now I have 7 discs left (2 per unit minus the one I swapped) just in case it happens again. Just order these, watch a YouTube video on how to take the controller apart and you can save a bunch of money and time. Wish I got these from the start.

Only giving it 4 stars since they definitely feel different from the originals. They feel a bit tighter and I prefer the lighter touch of the original. Other than that's they worked flawlessly. If you are new to soldering I would not recommend since removing can be tedious. For users who are comfortable with soldering then these are a breeze to replaced.

I ordered these over 5 years ago and finally got around to using one of them yesterday for an XBOX one controller. It worked great for fixing stick drift and was a nice part to have on hand.

I recently purchased the Onyehn 8pcs Controller 3D Analog Joystick Thumb Sticks Replacement to fix the joystick drift issue I was experiencing with my controller. The replacement sticks worked well to solve the initial drift problem, which was a relief. The installation was straightforward, and the parts fit perfectly without any noticeable defects.However, after using the new joysticks for a while, I noticed a significant downside. The joysticks are extremely sensitive, making it challenging to perform precise movements, especially in games that require fine control. This high sensitivity makes it hard to maintain steady aim or perform delicate maneuvers, leading to a somewhat frustrating gaming experience.In summary, while these replacements effectively fixed the drift issue, the overly sensitive response might not suit everyone, especially gamers who need precise joystick control. If you're just looking to eliminate drift, these might work for you, but be prepared for potentially increased sensitivity that could impact gameplay.

I don't know why a lot of people are saying not to use these, and only use the potentiometers off of them. The whole thing works fine for me. It feels like the stock ones that came on my original Xbox One controller. It's not "squishy" or whatever others have said. Maybe over time they'll wear out quicker, but that's the potentiometer, themselves. So, replacing just those wouldn't benefit you, anyway. However, it would require less soldering with the trade-off of more fiddling with tiny parts. If you're going to attempt this, either just replacing the pots or the whole thing, I'd suggest getting a solder sucker. I've done it in the past without one and it made it that much more of a time consuming pain in the ass. Also, some solder wick and flux is a good idea to have on hand.

After spending hours replacing these joysticks, my son said the controller was unusable for FPS games or shooting games as the axis movement is huge. Example. Normal joystick movement on a target might move your crosshairs millimeters across the screen at a time.... With these joysticks, the same slight movement of the joysticks moves the crosshairs over an inch across the screen. This makes it impossible to land the crosshairs on any target. DO NOT BUY AND WASTE YOUR TIME INSTALLING THESE.

I wouldn't use these as a full on replacement, but the potentiometers or sensor discs in them are good to fix stick drift. You might need to try more than one cuz they can be iffy in quality even for this purpose, but as long as you are careful no to damage the disc (which I might of for one) you should be gtg. If using in elite controller you will need to clip off the white plastic clips that stick out the green part once you close up your sensor to avoid contact with the motherboard. For the money this is a great product.

Cumple las expectativas..

Have bought 3 extra xbox controllers and all had the same stick Continuous drifting issues. I managed to ended up fixing one and replace another two and worked well after. Have to know the basics of desoldering and soldering the new peice but I had no issues. We now have 4 working controllers and we don't need to consider buying new ones again!

Make sure you know how to solder. Sometimes the solder pads may come off the controller and the drift will be worse than before. It is possible to solder on a new wire if that happens if you know what your doing.

J’ai regardé des vidéos sur le net pour voir comment remplacer la pièces. Vous aurez besoin d’outils spécialisés pour les visses, un bon fer à souder, une pompe à soudure et de la patience. Le plus difficile est de retirer l’ancienne pièce. Maintenant elle est comme une neuve ☺️ Manette de XBOX One

Bag it came with is scuffed with marks and tears. The analog sticks are sticky, they stick to one direction. Green part is off. Pins are bent.